
Polyisobutylene (PIB) is a polymer raw material for gasoline detergent components, not a finished additive. Manufacturers convert it into derivatives such as polyisobutylene amine (PIBA) and polyisobutylene succinic anhydride (PIBSA). Buyers should focus on molecular weight, terminal vinylidene content, viscosity and the intended synthesis route. Buyers new to the topic can start with what a PIB additive is.
Key Takeaways
- PIB is the raw material; derivatives such as PIBA do the cleaning in gasoline.
- High-reactivity PIB (HR-PIB) enables a chlorine-free thermal route to PIBSA.
- Dosage is set per additive package by engine testing, not by a fixed ppm figure.
- Ethanol changes additive solubility, so each formulation needs testing.
What Is a Polyisobutylene Gasoline Additive?
A polyisobutylene gasoline additive is a fuel additive whose active component is built on a PIB backbone. The PIB chain gives solubility in gasoline, while an attached polar group does the cleaning. PIBA and polyether amine (PEA) are the traditional detergents for intake valve deposit (IVD) control, although only PIBA is PIB-based.
| Term | Meaning |
|---|---|
| PIB | Polymer raw material |
| HR-PIB | High-reactivity PIB with a high share of terminal vinylidene double bonds |
| PIBSA | Maleic anhydride adduct of PIB, an intermediate for succinimide dispersants (PIBSI) |
| PIBA | Amine-functional PIB derivative used as a gasoline detergent |
| PEA | Polyetheramine, a separate non-PIB detergent chemistry |
PIB is also used in lubricants, adhesives and sealants, which have different requirements, as explained in choosing the right PIB grade for adhesives.
What Are PIB-Based Gasoline Additives Used For?
PIB-based gasoline additives are used to control deposits on intake valves and in fuel systems. Gasoline detergents are required in the United States for intake valve deposit control. An automaker bulletin shows the effect: valves run on fuel with the minimum detergent treat rate carried over 1,000 mg of deposits, against under 50 mg at a high treat rate.
Additive makers commonly describe PIBA as effective on injectors and intake valves and PEA as better for the combustion chamber, and patents describe PIBA–polyether mixtures that lower bench-test deposits.
How Is Dosage Determined?
No single dosage applies. A detergent manufacturer must establish the lowest additive concentration (LAC) through engine testing, and TOP TIER allows treat rates up to three times the approved minimum. Dosage therefore depends on the package, base fuel and test result.
How Is HR-PIB Turned into a Gasoline Detergent Component?
HR-PIB is converted mainly through PIBSA. Its terminal vinylidene double bonds react readily with maleic anhydride in a thermal "ene" reaction, and higher-functionality PIBSA can be made this way without chlorine, which conventional PIB cannot achieve. The PIBSA can then be converted into succinimide dispersants (PIBSI).
Simplified route: HR-PIB → PIBSA → PIBSI → additive formulation.
One patent reports PIBSA yields are generally 10 to 15% higher with HR-PIB. Chlorine routes are less attractive because environmental concerns related to chlorine-containing materials make them undesirable.
HR-PIB vs. Conventional PIB: What Is the Difference?
HR-PIB differs from conventional PIB mainly in terminal vinylidene content, which controls reactivity with maleic anhydride. HR-PIB supports a halogen-free route to PIBSA; conventional PIB generally does not.
| Comparison | HR-PIB | Conventional PIB |
|---|---|---|
| Terminal vinylidene content | High | Lower, mixed isomers |
| Halogen-free route to high-functionality PIBSA | Supported | Not achievable |
| Chlorine in the PIB itself | Can be made substantially chlorine-free | Depends on grade and process google |
Reported vinylidene thresholds for "HR-PIB" range from above 65% to above 85%. One patent describes commercial grades as about 83 to 85%. Rely on the supplier's certified result and test method.
Reactivity is not the same as detergency. One patent application reports detergents from conventional PIB performing better, pound for pound, than those from HR-PIB. Confirm grade choice by testing in your formulation.
Is PIB-Based Additive Compatible with Ethanol Gasoline?
Compatibility depends on the complete additive package and the ethanol level, so it must be tested rather than assumed. Conventional PIBA and PEA dissolve well in hydrocarbons but poorly in ethanol. Industry testing found ethanol tends to increase intake valve deposits, and some commercial detergent chemistries caused filter blocking in gasoline with 10% ethanol. Test the whole package, including the carrier oil, at each ethanol level.
Which Specifications Matter When Buying HR-PIB?
Check molecular weight, viscosity, terminal vinylidene content and chlorine content, each backed by a certified test method. Choose the grade by target derivative and validate it in a synthesis trial. the PIB grade and molecular weight guide explains how grades differ.
The table shows certificate of analysis (COA) data from example lots of two Tianjin Gnee Bio grades, in the format specification limit (example result).
| Item | Test method | PIB950 | GNPB-2400 |
|---|---|---|---|
| Appearance | Visual | Transparent | Transparent |
| Number-average molecular weight (Mn) | GB/T 21863 | No limit set (999) | No limit set (2441) |
| Viscosity at 100 °C, mm²/s | ASTM D445 | 230 ± 20 (238) | 5100 ± 150 (5114) |
| Color (Hazen, Pt-Co) | ASTM D1209 | ≤ 45 (15) | ≤ 45 (15) |
| Flash point (open cup), °C | GB/T 3536 | ≥ 200 (247) | ≥ 240 (269) |
| Water (Karl Fischer), wt-ppm | ASTM D6304 | ≤ 50 (21) | ≤ 50 (22) |
| Density at 20 °C, kg/m³ | GB/T 1884 | (887) | 900 ± 20 (902) |
Example lots: PIB950, lot 2025082605 (26 Aug 2025); GNPB-2400, lot 2025080302 (3 Aug 2025). Executive standard Q/HRD 002-2023. Results for each batch are reported on its COA.
For manufacturers looking for PIB raw materials for fuel detergent production, Polyisobutylene PIB 950 for Gasoline Additive is one available grade to evaluate based on molecular weight, viscosity, and downstream formulation requirements.
How to Request an HR-PIB Quotation
State the target derivative, required molecular weight, annual volume, packaging and destination port, and request the COA, TDS and SDS before ordering.
- Define the target derivative: PIBSA, PIBSI, PIBA or another product.
- Run a sample trial in your own synthesis process.
- Confirm terms: packaging, MOQ, lead time and shipping.
Looking for polyisobutylene raw materials for gasoline additive production? Request a Quote for Polyisobutylene Gasoline Additive Raw Material and send us your required molecular weight, viscosity, order quantity, and destination port.
FAQ
What is a PIB gasoline additive?
It is a fuel additive whose active component is a PIB-derived compound such as PIBA. PIB itself is the raw material, and performance depends on the derivative and the full formulation.
Is PIB the same as PIBA?
No. PIB is the polymer; PIBA is an amine-functional derivative made from it.
Why is HR-PIB used to make PIBSA?
Its terminal vinylidene double bonds react readily with maleic anhydride, allowing a halogen-free thermal route.
Is PIB-based additive compatible with ethanol gasoline?
It depends on the complete package. Ethanol changes solubility, so test each formulation at the intended ethanol level.


